CoreSight

coresight@lists.linaro.org

7 participants
2535 discussions

[PATCH v4 00/10] CoreSight configuration management; ETM strobing

by Mike Leach

This patchset introduces initial concepts in CoreSight system configuration management support. to allow more detailed and complex programming to be applied to CoreSight systems during trace capture. Configurations consist of 2 elements:- 1) Features - programming combinations for devices, applied to a class of device on the system (all ETMv4), or individual devices. 2) Configurations - a set of programmed features used when the named configuration is selected. Features and configurations are declared as a data table, a set of register, resource and parameter requirements. Features and configurations are loaded into the system by the virtual cs_syscfg device. This then matches features to any registered devices and loads the feature into them. Individual device classes that support feature and configuration register with cs_syscfg. Once loaded a configuration can be enabled for a specific trace run. Configurations are registered with the perf cs_etm event as entries in cs_etm/cs_config. These can be selected on the perf command line as follows:- perf record -e cs_etm/<config_name>/ ... This patch set has one pre-loaded configuration and feature. A named "strobing" feature is provided for ETMv4. A named "autofdo" configuration is provided. This configuration enables strobing on any ETM in used. Thus the command: perf record -e cs_etm/autofdo/ ... will trace the supplied application while enabling the "autofdo" configuation on each ETM as it is enabled by perf. This in turn will enable strobing for the ETM - with default parameters. Parameters can be adjusted using configfs. The sink used in the trace run will be automatically selected. A configuation can supply up to 15 of preset parameter values, which will subsitute in parameter values for any feature used in the configuration. Selection of preset values as follows perf record -e cs_etm/autofdo,preset=1/ ... (valid presets 1-N, where N is the number supplied in the configuration, not exceeding 15. preset=0 is the same as not selecting a preset.) Applies to coresight/next (5.11-rc2 base) Changes since v3: (Primarily based on comments from Matthieu) 1) Locking mechanisms simplified. 2) Removed the possibility to enable features independently from configurations.Only configurations can be enabled now. Simplifies programming logic. 3) Configuration now uses an activate->enable mechanism. This means that perf will activate a selected configuration at the start of a session (during setup_aux), and disable at the end of a session (around free_aux) The active configuration and associated features will be programmed into the CoreSight device instances when they are enabled. This locks the configuration into the system while in use. Parameters cannot be altered while this is in place. This mechanism will be extended in future for dynamic load / unload of configurations to prevent removal while in use. 4) Removed the custom bus / driver as un-necessary. A single device is registered to own perf fs elements and configfs. 5) Various other minor issues addressed. Changes since v2: 1) Added documentation file. 2) Altered cs_syscfg driver to no longer be coresight_device based, and moved to its own custom bus to remove it from the main coresight bus. (Mathieu) 3) Added configfs support to inspect and control loaded configurations and features. Allows listing of preset values (Yabin Cui) 4) Dropped sysfs support for adjusting feature parameters on the per device basis, in favour of a single point adjustment in configfs that is pushed to all device instances. 5) Altered how the config and preset command line options are handled in perf and the drivers. (Mathieu and Suzuki). 6) Fixes for various issues and technical points (Mathieu, Yabin) Changes since v1: 1) Moved preloaded configurations and features out of individual drivers. 2) Added cs_syscfg driver to manage configurations and features. Individual drivers register with cs_syscfg indicating support for config, and provide matching information that the system uses to load features into the drivers. This allows individual drivers to be updated on an as needed basis - and removes the need to consider devices that cannot benefit from configuration - static replicators, funnels, tpiu. 3) Added perf selection of configuarations. 4) Rebased onto the coresight module loading set. To follow in future revisions / sets:- a) load of additional config and features by loadable module. b) load of additional config and features by configfs c) enhanced resource management for ETMv4 and checking features have sufficient resources to be enabled. d) ECT and CTI support for configuration and features. Mike Leach (10): coresight: syscfg: Initial coresight system configuration coresight: syscfg: Add registration and feature loading for cs devices coresight: config: Add configuration and feature generic functions coresight: etm-perf: update to handle configuration selection coresight: syscfg: Add API to activate and enable configurations coresight: etm-perf: Update to activate selected configuration coresight: etm4x: Add complex configuration handlers to etmv4 coresight: config: Add preloaded configurations coresight: syscfg: Add initial configfs support coresight: docs: Add documentation for CoreSight config .../trace/coresight/coresight-config.rst | 244 ++++++ Documentation/trace/coresight/coresight.rst | 16 + drivers/hwtracing/coresight/Makefile | 7 +- .../hwtracing/coresight/coresight-cfg-afdo.c | 154 ++++ .../coresight/coresight-cfg-preload.c | 25 + .../coresight/coresight-cfg-preload.h | 11 + .../hwtracing/coresight/coresight-config.c | 246 ++++++ .../hwtracing/coresight/coresight-config.h | 282 +++++++ drivers/hwtracing/coresight/coresight-core.c | 18 +- .../hwtracing/coresight/coresight-etm-perf.c | 180 ++++- .../hwtracing/coresight/coresight-etm-perf.h | 12 +- .../hwtracing/coresight/coresight-etm4x-cfg.c | 184 +++++ .../hwtracing/coresight/coresight-etm4x-cfg.h | 29 + .../coresight/coresight-etm4x-core.c | 38 +- .../coresight/coresight-etm4x-sysfs.c | 3 + .../coresight/coresight-syscfg-configfs.c | 399 +++++++++ .../coresight/coresight-syscfg-configfs.h | 45 ++ .../hwtracing/coresight/coresight-syscfg.c | 761 ++++++++++++++++++ .../hwtracing/coresight/coresight-syscfg.h | 90 +++ include/linux/coresight.h | 7 + 20 files changed, 2721 insertions(+), 30 deletions(-) create mode 100644 Documentation/trace/coresight/coresight-config.rst create mode 100644 drivers/hwtracing/coresight/coresight-cfg-afdo.c create mode 100644 drivers/hwtracing/coresight/coresight-cfg-preload.c create mode 100644 drivers/hwtracing/coresight/coresight-cfg-preload.h create mode 100644 drivers/hwtracing/coresight/coresight-config.c create mode 100644 drivers/hwtracing/coresight/coresight-config.h create mode 100644 drivers/hwtracing/coresight/coresight-etm4x-cfg.c create mode 100644 drivers/hwtracing/coresight/coresight-etm4x-cfg.h create mode 100644 drivers/hwtracing/coresight/coresight-syscfg-configfs.c create mode 100644 drivers/hwtracing/coresight/coresight-syscfg-configfs.h create mode 100644 drivers/hwtracing/coresight/coresight-syscfg.c create mode 100644 drivers/hwtracing/coresight/coresight-syscfg.h -- 2.17.1

4 years, 8 months

Vos besoins en traduction-Translations

by "Interprètes & traductions professionnelles -toutes langues officielles"

Bonjour, Je me permets de vous écrire afin de vous proposer nos services de traduction et d’interprétariat. Disposez-vous déjà d'une agence partenaire ? Notre agence, qui compte parmi les leaders du marché français de la traduction, peut intégralement prendre en charge vos projets multilingues. Notre agence, basée en France, vous propose: - Un gestionnaire de projet dédié à votre entreprise. - La garantie du respect de la confidentialité de vos documents à traduire. - Une qualité de traduction irréprochable dans tous les domaines. - Une réactivité sans égale. - La possibilité de profiter de la parité avantageuse Franc Suisse / Euro. Voici quelques-unes de nos références: Disney nature, L'Oréal Luxe , Bourbon, La Méridionale, Dailymotion, Saint Gobain, Audemars PIGUET, Pierre Hermé, Airbusiness Academy, Blanchefontaine SA, C-discount, Gretz Communication, Luminox, Hugo Boss, Axa groupe, International Labour Office (BIT), CNRS, LA Recherche Magazine, Puy du Fou International, WWF…vous trouverez toutes les autres sur notre site internet. N'hésitez surtout pas à me demander un devis gratuit via cette même adresse mail svp, Bien cordialement, Jean-Christophe Supot Dear Sir or Madam, I am writing to you to propose our translation services. Do you already work with a partner agency? Our agency, a leader in the French translation market, can deliver your multilingual projects or those of your clients. Our France-based agency offers you: - A project manager dedicated to your account - The complete confidentiality of your documents - Irreproachable translation quality in all fields. - Unequalled quick response time - The possibility to take advantage of the exchange rate between the Euro and Swiss Franc. Some of our references: Disney nature, L'Oréal Luxe , Bourbon, La Méridionale, Dailymotion, Saint Gobain, Audemars PIGUET, Pierre Hermé, Airbusiness Academy, Blanchefontaine SA, C-discount, Gretz Communication, Luminox, Hugo Boss, Axa groupe, International Labour Office (BIT), CNRS, LA Recherche Magazine, Puy du Fou International, WWF…amongst many others that you can find on our website. Please feel free to request a free quotation by writing to this email address. Best regards, Jean-Christophe Supot

4 years, 8 months

【重要】カード情報更新のお知らせ

by Amazon.co.jp

Аmazon お客様 coresight(a)lists.linaro.org АmaNRHR146146zon に登録いただいたNRHR505543お客様に、АmaNRHR276669zon アカウントの情報更NRHR168095新をお届けします。残念NRHR399746ながら、АmNRHR335724azoNRHR53739n のアカウントをNRHR320034更新できませんNRHR270690でした。今回は、カードが期限NRHR78753切れになってるか、請求NRHR201443先住所が変NRHR427591更されたなど、さまNRHR150423ざまな理由でカーNRHR272914ドの情報を更NRHR384293新できませNRHR343749んでした。アカウント情報のNRHR1348一部が誤っている故NRHR412297に、お客様のアNRHR26048カウントをNRHR524067維持するためNRHR283024 АmaNRHR395700zon アカウンNRHR141388トの情報を確認すNRHR392167る必要があります。下かNRHR176560らアカウントをログイNRHR13888ンし、情報を更NRHR83307新してください。 Аmazon ログインなお、24時NRHR447337間以内にご確NRHR108373認がない場合、誠に申しNRHR23715訳ございません、おNRHR299962客様の安全の為、アカNRHR46576ウントの利用制限をさNRHR243125せていただきますNRHR170431ので、予NRHR36005めご了NRHR352897承ください。アカウNRHR458966ントに登録NRHR452180のEメールアNRHR120325ドレスにアクセスでNRHR118262きない場合お問い合わせ： Amazonカスタマーサービス。お知らせ: パスワードは誰にNRHR114981も教えないNRHR335312でください。個人情NRHR85549報と関係がなNRHR5799く、推測しにくいNRHR74509パスワードを作NRHR141861成してください。大文字とNRHR333071小文字、数字、およびNRHR46356記号を必ずNRHR452708使用してください。オンライNRHR120985ンアカウントNRHR344248ごとに、異なるパNRHR240750スワードをNRHR445711使NRHR480450用してください。どうぞよろNRHR117254しくお願いいたNRHR494125します。 Аmazon

4 years, 8 months

Hallo und Guten Tag,

by El Gordo de la primitiva lotterie spanien

El Gordo de la primitiva lotterie spanien Adresse:Calle del Príncipe de Vergara, 38, 28001 Madrid España] Kontakt aufnehmen unter:] 34602 810 185 fax 34935457490] E-mail:]anspruchgewinn.mmt.es@spainmail.com] Aktenzeichen:]P09/01/02/2021.] Losnummer:] ESP 4447/1146411880201] Datum: 06/03/2021] Hallo, OFFIZIELLE MITTEILUNG, Diese El Gordo de la Primitiva Bonanza Lotterie wurde und Ministerio de Industria, Comercio y Turismo gesponsert um Tourismus in Spanien zu fördern. Wir sind erfreut Ihnen mit zu teilen, dass die Gewinner des Sonder Spanish Tourismus Promotional Draw bekannt gegeben worden sind. Die offizielle Liste der Gewinner erschien am Samstag der 27/01/2021. Ihre email adresse mit der anhängenden Losnummer: ESP 4447/1146411880201 und mit der Seriennummer: ESP/018811-2020 zog die Glücksnummer: 6.16.18.33.47.51 Bonu:29,El Gordo de la Primitiva Lotterie 6 /49 in der 3. Kategorie. Sie sind damit gewinner von: €991,000.00 Euro. Die Summe ergibt sich aus einer Gewinnausschüttung von: €6937,000.00 Euro, die durch die ersten sieben (7) Gewinner aus der gleichen Kategorie geteilt wurde. Dir gewinn ist bei einer sicherheitsfirma hinterlegt und in ihren namen/email versichert. um keine komplikationen bei der abwicklung der zahlung zu verursachen bitten wir sie diese offizielle mitteilung , diskret zu behandeln.,es ist ein teil unseres sicherheitsprotokolls und garantiert ihnen einen reibungslosen Ablauf. Alle gewinner wurden per computer aus Urlaubshotels, Fluggesellschaften und Reisebüros mailen Daten von fünf Millionen (5000000) Email adressen ausgewählt, als teil unserer Internationalen tourismus promotion programms, welches wir einmal im jahr veranstalten um Tourismus in Spanien zu fördern. Bitte kontaktieren sie unseren auslands sachbearbeiter Herr Gabriel bei der sicherheitsfirma Santalucia Sicherheitsfirma:Per Email an:europromo.es.spain@europemail.com oder anrufen: 34 602 810 185 & Fax: 34 931 70 2120, um Ihr Geld schnell zu bekommen. Denken Sie daran, jeder gewinnanspruch muss bis zum 31/03/2021 Angemeldete sein. Jeder nicht angemeldet Gewinnanspruch verfällt und geht zuruck an das Spanische Staatskasse. WICHTIG: um verzögerungen und komplikationen zu vermeiden, bitte immer Aktenzeichen angeben. Anbei ein anmeldeformular, bitte ausfüllen und zurück Per email an:europromo.es.spain@europemail.com oder anrufen: 34 602 810185 & Fax: 34 931 70 2120 die sicherheitsfirma Santalucia Sicherheitsfirma. HERZLICHEN GLUCKWUNSCH…! Mit freundlichen Grüßen MARIA HIDALGO VIZEPRÄSIDENTIN BÜRO,SANTALUCIA SEGUROS S.A España Plaza España, 15 - -16 Madrid, 28008 España ANMELDEFORMULAR ZUR GEWINNANSPRUCHS _____________________________________________ Bitte füllen Sie das Formular sorgfältig aus und senden es per e mail:santalucia.sg.es@spainmail.com an der Santalucia Sicherheitsfirma mit Kopie Ihres Personalausweises oder Reisepasses. GEWINNBETRAG*__________AKTENZEICHEN:*ESP09/01/02/2021 NAME:*____________________VORNAME:*_______________________ GEBURTSDATUM:*_________________*NATIONALI:*________________ LOSNUMMER*______________________*GLUCKSZAHLEN:*____________ STRASSE*____________________________*NUMMER:*_______________ WOHNORT*________________POSTLEITZAH*__________*LAND*________ TELEFON*____________HANDY*_____________FAX*_________________ BEFUF*__________FAMIELIENSTAND*_______________* (GESCHLECHT) EMAIL*________________________________________*Unterschrift*_ WELCHE ZAHLUNGSFORM BEVORZUGEN SIE? (A) BANKÜBERWEISUNG: (B) BARSCHECK BANKDATEN SIND NUR NOTWENDIG WENN SIE SICH FÜR EINE BANKÜBERWEISUNG ENTSCHIEDEN HABEN. NAME DES GELDINSTITUTS:*__________________________ KONTONUMMER:*_____________________________________ SWIFT CODE:*______________________________________ BANK ADDRESS:*____________________________________ TELEFONNUMMER:*___________________________________ FAX: NUMMER:*_____________________________________ ERKLÄRUNG DES BEGÜNSTIGTEN ICH ___________________________BESTÄTIGE HIERMIT, DASS ALLE INFORMATIONEN, KORREKT SIND, UND DIE VERANSTALTER DER El SPANISH LOTTERY / SANTALUCIA SICHERHEITSFIRMA NICHT VERANTWORTLICH GEMACHT WERDEN, WENN ES ZU EINER UNBERECHTIGTEN ZAHLUNG DURCH UNGENAUE INFORMATIONEN, DIE ICH IN DIESEM FORMULAR ANGEBE KOMMT.DASS 10% PROVISION DER SANTA LUCIA SECURITY COMPANY GEH?REN, SOBALD SIE IHREN GEWINN FONDS ERHALTEN. DIESE ZEHN PROZENT WERDEN IHNEN SOFORT ZURÜCKGEGEBEN, SIE ERHALTEN IHREN GEWINN AUF IHREM KONTO. (ACHTUNG Wir bitten Sie, auf diese E-Mail-Adresse zu antworten(santalucia.sg.es(a)spainmail.com) BÜRO-KONTOINFORMATIONEN-IBAN ES17 2100 5624 1102 0011 7719 SWIFT CODE: CAIXESBBXXX. KONTONAME,LA PLACITA DEL MIRADOR S.L SPAIN. Urheberrecht© 2020-2021 Multi-Staat Lotterie Verband. Alle Rechte

4 years, 8 months

Attention,mailbox is 98% full

by lists.linaro.org

4 years, 8 months

Attention,mailbox is 98% full

by lists.linaro.org

4 years, 8 months

Re: Secure World Coresight Tracing - HiKey 960

by Mike Leach

Hi Daniel, The CoreSight mailing list is the best place to ask these questions - I've added it to the to: section of this mail. On Fri, 19 Feb 2021 at 13:43, Daniel Su <daniel.sun.su(a)gmail.com> wrote: > > Sorry I made a mistake, I need to switch those bits but those aren't in the ETM mode sysFS parameter. > > > On Feb 19, 2021, at 14:21, Daniel Su <daniel.sun.su(a)gmail.com> wrote: > > > > Thanks, > > > > To just give a bit of background I am doing an internship to improve tracing and debugging for secure world applications in TrustZone. Originally the idea was to come up with a software solution but I thought using the hardware tracing features might be very powerful as the secure world trusted execution environments typically have less debugging and tracing functionalities built into the trusted operating system. > > > > I have been doing further reading and I believe I need to configure the ETM mode sysFS parameter. > > > > To switch these bits: > > > > /* secure state access levels - TRCACATRn */ > > #define ETM_EXLEVEL_S_APP BIT(8) > > #define ETM_EXLEVEL_S_OS BIT(9) > > #define ETM_EXLEVEL_S_HYP BIT(10) > > #define ETM_EXLEVEL_S_MON BIT(11) > > /* non-secure state access levels - TRCACATRn */ > > #define ETM_EXLEVEL_NS_APP BIT(12) > > #define ETM_EXLEVEL_NS_OS BIT(13) > > #define ETM_EXLEVEL_NS_HYP BIT(14) > > #define ETM_EXLEVEL_NS_NA BIT(15) > > ns_exlevel_vinst and s_exlevel_vinst control these bits in the TRCVICTLR. addr_exlevel_s_ns sets both S and NS bits in the TRCACATRn register currently addressed by addr_idx. In the kernel tree - Documentation/trace/coresight/coresight-etm4x-reference.rst - has lots of information on programming these sysfs files. I would advise setting mode first - which will set up some default values for TRCVITLR, then make any further adjustments you want. > > Right now I am able to capture the traces and read them out thanks to Leo Yan's command examples and presentation. > > > > I still need to figure out how to only trace branching instructions, and also how to best decode the traces. Right now even though I can read out /dev/ec036000.etf , I am unsure how to best go about interpreting the raw trace data. > > Hardware trace will trace everything - subject to certain filters - such as address filtering, exception filtering etc. It is not possible to trace only branch instructions. You will need to capture trace, decode then run an analysis on that decode to determine what branches have been taken. ETMv4 is program flow trace - so all branches are marked as taken or not taken. Consider the program:- =============== 0x1000 start: < some code > ... 0x1100 B func1 0x1200 func1: <some code> .... 0x1240 mov r0, &func2 B r0 0x2000 func2: <some code> ================ This will result in trace as follows:- TRACE_ON ADDR(0x1000) ATOM(E) > > I believe ptm2human and OpenCSD are two open source libraries that allow for decoding of the ETMv4 trace data. I understand there are paid solutions as well such as the DS-5 and Trace32 from Lauterbach to decode. > > > > Do you have any recommendations on other decoders or any tips in general as to how to decode the raw trace data into human readable format? > > > > Best, > > Daniel > > > >> On Feb 18, 2021, at 18:38, Suzuki K Poulose <suzuki.poulose(a)arm.com> wrote: > >> > >> Hi Daniel > >> > >> On 2/18/21 4:12 PM, Daniel Su wrote: > >>> Hello, > >>> First of all I want to say thanks for your work on the Coresight support as well as the presentation slides. Currently I am working with the Hikey960 which I see is supported and has been used as a reference platform in your slides. > >>> I believe it should be possible to setup self-hosted Coresight to trace only for branch instructions in the secure world. Currently I am investigating how to set this up on the Hikey960 without access to a hardware debugger. > >>> I am wondering if any of you have done this before, if there is additional documentation, or if there are any good support groups/chats/channels to ask questions. I have some experience with Coresight mainly from reading the ARM reference manuals but it is still a lot to parse. > >> > >> I haven't done anything similar. You should be able to imitate how the > >> CoreSight drivers program the components ( ETM, Funnels, Replicator and ETR). > >> > >> For ETM, you just need to make sure you don't filter out the Secure EL1/EL2/EL0. > >> You would need to read the manuals for the components or user the kernel driver > >> as the reference. > >> > >> Cheers > >> Suzuki > >> > >>> I believe in Linux I should be using `ns_exlevel_vinst` to filter out Non-Secure instructions. Also since the Hikey960 is multicore, I guess I would need to configure the top level Coresight in order to trace all cores? Would this be the ETR then? > >>> Best, > >>> Daniel > >> > > > -- Mike Leach Principal Engineer, ARM Ltd. Manchester Design Centre. UK

4 years, 8 months

[PATCH -next] coresight: etm: perf: Make symbol 'format_attr_contextid' static

by 'Wei Yongjun

From: Wei Yongjun <weiyongjun1(a)huawei.com> The sparse tool complains as follows: drivers/hwtracing/coresight/coresight-etm-perf.c:61:25: warning: symbol 'format_attr_contextid' was not declared. Should it be static? This symbol is not used outside of coresight-etm-perf.c, so this commit marks it static. Reported-by: Hulk Robot <hulkci(a)huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1(a)huawei.com> --- drivers/hwtracing/coresight/coresight-etm-perf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hwtracing/coresight/coresight-etm-perf.c b/drivers/hwtracing/coresight/coresight-etm-perf.c index 0f603b4094f2..bdbb77334329 100644 --- a/drivers/hwtracing/coresight/coresight-etm-perf.c +++ b/drivers/hwtracing/coresight/coresight-etm-perf.c @@ -58,7 +58,7 @@ static ssize_t format_attr_contextid_show(struct device *dev, return sprintf(page, "config:%d\n", pid_fmt); } -struct device_attribute format_attr_contextid = +static struct device_attribute format_attr_contextid = __ATTR(contextid, 0444, format_attr_contextid_show, NULL); static struct attribute *etm_config_formats_attr[] = {

4 years, 8 months

Attention,kindly follow instruction before 48hrs

by lists.linaro.org

4 years, 8 months

Attention,mailbox storage is 98% full

by lists.linaro.org

4 years, 8 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

CoreSight