Failed boards:
omap5uevm omap2plus_defconfig : FAILED 1:46.01 omap5uevm multi_v7_defconfig : FAILED 1:49.17 omap5uevm multi_lpae_defconfig : FAILED 1:47.81 snow multi_v7_defconfig : FAILED 1:11.23 snow multi_lpae_defconfig : FAILED 1:11.94 snowball u8500_defconfig : FAILED 1:56.50
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:14.45 arndale exynos_defconfig : passed 1:12.07 arndale multi_v7_defconfig : passed 1:37.63 arndale multi_lpae_defconfig : passed 1:21.43 bbb omap2plus_defconfig : passed 1:30.93 bbb multi_v7_defconfig : passed 1:27.93 beaver tegra_defconfig : passed 1:05.32 beaver multi_v7_defconfig : passed 1:05.89 capri bcm_defconfig : passed 0:39.29 capri multi_v7_defconfig : passed 0:39.49 cubie sunxi_defconfig : passed 1:17.37 cubie multi_v7_defconfig : passed 1:25.01 cubie2 sunxi_defconfig : passed 1:15.55 cubie2 multi_v7_defconfig : passed 1:31.82 cubie2 multi_lpae_defconfig : passed 1:22.13 cubox multi_v7_defconfig : passed 1:01.85 dalmore tegra_defconfig : passed 1:25.98 dalmore multi_v7_defconfig : passed 1:27.53 dalmore multi_lpae_defconfig : passed 1:24.73 hummingboard imx_v6_v7_defconfig : passed 1:28.05 hummingboard multi_v7_defconfig : passed 1:13.52 jetson tegra_defconfig : passed 1:01.17 jetson multi_v7_defconfig : passed 0:54.51 jetson multi_lpae_defconfig : passed 1:10.19 panda omap2plus_defconfig : warnings 1:30.57 panda multi_v7_defconfig : warnings 1:42.46 sama5 sama5_defconfig : warnings 1:55.63 seaboard tegra_defconfig : passed 1:03.61 seaboard multi_v7_defconfig : passed 1:11.37 snow exynos_defconfig : passed 1:28.67 snowball multi_v7_defconfig : passed 2:33.25 trimslice tegra_defconfig : passed 1:15.16 trimslice multi_v7_defconfig : passed 1:04.14 wandboard imx_v6_v7_defconfig : passed 1:01.87 wandboard multi_v7_defconfig : passed 1:13.72
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.087777] NET: Registered protocol family 17 [ 47.087805] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.097311] mmcblk0: unknown partition table [ 47.098096] mmcblk0boot1: unknown partition table [ 47.098861] mmcblk0boot0: unknown partition table [ 47.113180] can: controller area network core (rev 20120528 abi 9) [ 47.119678] NET: Registered protocol family 29 [ 47.124328] can: raw protocol (rev 20120528) [ 47.128797] can: broadcast manager protocol (rev 20120528 t) [ 47.134719] can: netlink gateway (rev 20130117) max_hops=1 [ 47.140728] Key type dns_resolver registered [ 47.145254] omap_vc_init_channel: No PMIC info for vdd_core [ 47.151080] omap_vp_init: No PMIC info for vdd_core [ 47.156177] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.161823] omap_vp_init: No PMIC info for vdd_mm [ 47.166744] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.172472] omap_vp_init: No PMIC info for vdd_mpu [ 47.177764] ThumbEE CPU extension supported. [ 47.182244] Registering SWP/SWPB emulation handler [ 47.188447] palmas 0-0048: Irq flag is 0x00000000 [ 47.196194] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.203782] smps123: 600 <--> 1500 mV at 1060 mV [ 47.209913] smps45: 600 <--> 1310 mV at 1030 mV [ 47.216363] smps6: 1200 mV [ 47.220361] smps7: 1800 mV [ 47.224492] smps8: 600 <--> 1310 mV at 1040 mV [ 47.230217] smps9: failed to get the current voltage [ 47.235462] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.247511] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.371952] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.516959] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.523051] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.530501] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.537363] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.545077] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 47.558457] ALSA device list: [ 47.561551] No soundcards found. [ 47.565553] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout Board omap5uevm-multi_v7_defconfig failure log: -------------------------------------------------
[ 47.537490] NET: Registered protocol family 17 [ 47.537517] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.547042] mmcblk0: unknown partition table [ 47.547821] mmcblk0boot1: unknown partition table [ 47.548571] mmcblk0boot0: unknown partition table [ 47.562897] can: controller area network core (rev 20120528 abi 9) [ 47.569402] NET: Registered protocol family 29 [ 47.574047] can: raw protocol (rev 20120528) [ 47.578509] can: broadcast manager protocol (rev 20120528 t) [ 47.584428] can: netlink gateway (rev 20130117) max_hops=1 [ 47.590451] Key type dns_resolver registered [ 47.594980] omap_vc_init_channel: No PMIC info for vdd_core [ 47.600799] omap_vp_init: No PMIC info for vdd_core [ 47.605901] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.611543] omap_vp_init: No PMIC info for vdd_mm [ 47.616447] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.622185] omap_vp_init: No PMIC info for vdd_mpu [ 47.627474] ThumbEE CPU extension supported. [ 47.631945] Registering SWP/SWPB emulation handler [ 47.638155] palmas 0-0048: Irq flag is 0x00000000 [ 47.645846] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.653394] smps123: 600 <--> 1500 mV at 1060 mV [ 47.659528] smps45: 600 <--> 1310 mV at 1030 mV [ 47.665948] smps6: 1200 mV [ 47.669915] smps7: 1800 mV [ 47.674023] smps8: 600 <--> 1310 mV at 1040 mV [ 47.679769] smps9: failed to get the current voltage [ 47.685017] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.697078] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.821672] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.966681] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.972759] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.980196] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.987047] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.994769] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.008162] ALSA device list: [ 48.011257] No soundcards found. [ 48.015257] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 1.950708] Key type dns_resolver registered [ 1.950806] omap_vc_init_channel: No PMIC info for vdd_core [ 1.950809] omap_vp_init: No PMIC info for vdd_core [ 1.950819] omap_vc_init_channel: No PMIC info for vdd_mm [ 1.950822] omap_vp_init: No PMIC info for vdd_mm [ 1.950831] omap_vc_init_channel: No PMIC info for vdd_mpu [ 1.950834] omap_vp_init: No PMIC info for vdd_mpu [ 1.951389] ThumbEE CPU extension supported. [ 1.951411] Registering SWP/SWPB emulation handler [ 1.951423] SmartReflex Class3 initialized [ 2.015758] palmas 0-0048: Irq flag is 0x00000000 [ 2.033323] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.039721] mmc0: new high speed MMC card at address 0001 [ 2.047485] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.052770] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.059236] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.068502] mmcblk0: unknown partition table [ 2.075108] mmcblk0boot1: unknown partition table [ 2.081764] mmcblk0boot0: unknown partition table [ 2.103059] smps123: 600 <--> 1500 mV at 1060 mV [ 2.110070] smps45: 600 <--> 1310 mV at 1030 mV [ 2.117447] smps6: 1200 mV [ 2.122238] smps7: 1800 mV [ 2.127130] smps8: 600 <--> 1310 mV at 1040 mV [ 2.133628] smps9: failed to get the current voltage [ 2.139637] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.153974] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.162817] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.170737] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.176803] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.185947] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.195348] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.202318] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.210787] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.219455] sr_init: No PMIC hook to init smartreflex [ 2.224911] sr_init: platform driver register failed for SR [ 2.253090] pbias_mmc_omap5: disabling [ 2.258586] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout Board snow-multi_lpae_defconfig failure log: -------------------------------------------------
[ 2889.881378] No ATAGs? [ 2889.881396] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.881402] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.881497] EXYNOS5250 PMU Initialize [ 2889.882705] Serial: AMBA PL011 UART driver [ 2920.594305] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 2920.594317] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 2920.594610] vbat-supply: no parameters [ 2920.594752] P5.0V_USB3CON: 5000 mV [ 2920.595885] vgaarb: loaded [ 2920.596158] SCSI subsystem initialized [ 2920.596239] libata version 3.00 loaded. [ 2920.596385] usbcore: registered new interface driver usbfs [ 2920.596414] usbcore: registered new interface driver hub [ 2920.596466] usbcore: registered new device driver usb [ 2920.596884] Linux video capture interface: v2.00 [ 2920.596908] pps_core: LinuxPPS API ver. 1 registered [ 2920.596912] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 2920.596926] PTP clock support registered [ 2920.596969] EDAC MC: Ver: 3.0.0 [ 2920.597324] Advanced Linux Sound Architecture Driver Initialized. [ 2920.597781] Switched to clocksource arch_sys_counter [ 2920.602026] NET: Registered protocol family 2 [ 2920.602272] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 2920.602309] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 2920.602382] TCP: Hash tables configured (established 8192 bind 8192) [ 2920.602409] TCP: reno registered [ 2920.602416] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 2920.602433] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 2920.602512] NET: Registered protocol family 1 [ 2920.602652] RPC: Registered named UNIX socket transport module. [ 2920.602656] RPC: Registered udp transport module. [ 2920.602660] RPC: Registered tcp transport module. [ 2920.602664] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2920.602674] PCI: CLS 0 bytes, default 64 [ 2920.603011] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available [ 2920.603692] futex hash table entries: 512 (order: 3, 32768 bytes) [ 2920.609163] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2920.609521] NFS: Regist~$off # PYBOOT: Exception: timeout Board snow-multi_v7_defconfig failure log: -------------------------------------------------
[ 2920.602341] TCP: reno registered [ 2920.602348] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 2920.602365] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 2920.602446] NET: Registered protocol family 1 [ 2920.602578] RPC: Registered named UNIX socket transport module. [ 2920.602583] RPC: Registered udp transport module. [ 2920.602587] RPC: Registered tcp transport module. [ 2920.602590] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2920.602601] PCI: CLS 0 bytes, default 64 [ 2920.602930] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available [ 2920.603601] futex hash table entries: 512 (order: 3, 32768 bytes) [ 2920.608863] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2920.609215] NFS: Registering the id_resolver key type [ 2920.609233] Key type id_resolver registered [ 2920.609237] Key type id_legacy registered [ 2920.609264] msgmni has been set to 1464 [ 2920.609498] bounce: pool size: 64 pages [ 2920.609597] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 2920.609607] io scheduler noop registered [ 2920.609615] io scheduler deadline registered [ 2920.609699] io scheduler cfq registered (default) [ 2920.612340] backlight supply power not found, using dummy regulator [ 2920.612392] pwm-backlight backlight: unable to request PWM, trying legacy API [ 2920.612398] pwm-backlight backlight: unable to request legacy PWM [ 2920.612435] platform backlight: Driver pwm-backlight requests probe deferral [ 2920.612623] simple-framebuffer bfc00000.framebuffer: framebuffer at 0xbfc00000, 0x202000 bytes, mapped to 0xf0400000 [ 2920.612629] simple-framebuffer bfc00000.framebuffer: format=r5g6b5, mode=1366x768x16, linelength=2732 [ 2920.615424] Console: switching to colour frame buffer device 170x48 [ 2920.618013] simple-framebuffer bfc00000.framebuffer: fb0: simplefb registered! [ 2920.619790] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-2364208 [ 2920.619797] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2920.621093] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-2364208 [ 2920.621100] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2920.621477] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-2364208 [ 2920.621484] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 2920.621854] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-2364208 [ 2920.621861] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 2920.647009] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2920.647912] 12c00000.serial: ttySA~$off # PYBOOT: Exception: timeout Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.539154] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.551086] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.558380] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.569854] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.578430] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.590362] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.597686] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.609161] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.616973] HS USB OTG: no transceiver configured [ 3.621704] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.629547] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.637481] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.649414] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.656738] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.668212] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.676788] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.688720] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.696044] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.707519] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.715332] HS USB OTG: no transceiver configured [ 3.720031] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.727905] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.735839] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.747741] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.755065] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.766571] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.775146] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.787078] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.794403] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.805877] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.813690] HS USB OTG: no transceiver configured [ 3.818389] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.826263] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.834197] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.846130] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.853424] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.864929] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.873504] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto ~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org