Failed boards:
cubie2 sunxi_defconfig : FAILED 1:18.83 panda multi_v7_defconfig : FAILED 1:35.10 snowball multi_v7_defconfig : FAILED 1:10.27
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:13.56 arndale exynos_defconfig : passed 1:02.82 bbb omap2plus_defconfig : passed 1:33.62 bbb multi_v7_defconfig : passed 1:21.28 beaver tegra_defconfig : passed 0:49.87 beaver multi_v7_defconfig : passed 0:52.59 capri bcm_defconfig : passed 0:44.70 capri multi_v7_defconfig : passed 0:45.28 cubie sunxi_defconfig : passed 1:03.56 cubie multi_v7_defconfig : passed 1:34.07 cubie2 multi_v7_defconfig : passed 1:42.32 cubie2 multi_lpae_defconfig : passed 1:27.95 dalmore tegra_defconfig : passed 1:24.29 dalmore multi_v7_defconfig : passed 1:20.47 dalmore multi_lpae_defconfig : passed 1:17.78 hummingboard imx_v6_v7_defconfig : passed 1:22.04 hummingboard multi_v7_defconfig : passed 1:07.87 omap5uevm omap2plus_defconfig : warnings 1:16.61 omap5uevm multi_v7_defconfig : warnings 1:44.12 omap5uevm multi_lpae_defconfig : warnings 1:42.13 panda omap2plus_defconfig : warnings 1:15.52 sama5 sama5_defconfig : passed 1:52.42 seaboard tegra_defconfig : passed 1:03.10 seaboard multi_v7_defconfig : passed 1:08.13 snow exynos_defconfig : passed 1:29.27 snowball u8500_defconfig : passed 1:13.00 trimslice tegra_defconfig : passed 0:58.86 trimslice multi_v7_defconfig : passed 1:02.72 wandboard imx_v6_v7_defconfig : passed 0:56.16 wandboard multi_v7_defconfig : passed 0:52.44
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.017665] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017692] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017705] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017725] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017737] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018674] Switched to clocksource arch_sys_counter [ 0.025795] NET: Registered protocol family 2 [ 0.026258] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026348] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026469] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026554] TCP: reno registered [ 0.026568] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026625] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026824] NET: Registered protocol family 1 [ 0.027215] RPC: Registered named UNIX socket transport module. [ 0.027227] RPC: Registered udp transport module. [ 0.027233] RPC: Registered tcp transport module. [ 0.027239] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028203] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028750] bounce pool size: 64 pages [ 0.036488] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036506] io scheduler noop registered [ 0.036512] io scheduler deadline registered [ 0.036692] io scheduler cfq registered (default) [ 0.038341] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080411] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.082828] console [ttyS0] disabled [ 0.103026] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.618429] console [ttyS0] enabled [ 0.623140] mousedev: PS/2 mouse device common for all mice [ 0.629015] i2c /dev entries driver [ 0.633818] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.642808] TCP: cubic registered [ 0.646129] NET: Registered protocol family 17 [ 0.650695] Registering SWP/SWPB emulation handler [ 0.656408] ahci-5v: 5000 mV [ 0.659696] usb1-vbus: 5000 mV [ 0.663060] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout
========================================================================
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.632019] omap_hsmmc 480d5000.mmc: unable to get vmmc regulator -517 [ 1.638916] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.646820] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.653686] usbcore: registered new interface driver usbhid [ 1.659545] usbhid: USB HID core driver [ 1.667510] TCP: cubic registered [ 1.670989] NET: Registered protocol family 17 [ 1.675842] Key type dns_resolver registered [ 1.680816] Power Management for TI OMAP4+ devices. [ 1.685943] Power Management for TI OMAP4. [ 1.690277] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.697662] ThumbEE CPU extension supported. [ 1.702148] Registering SWP/SWPB emulation handler [ 1.707855] vwl1271: 1800 mV [ 1.713104] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.722290] twl 0-0048: PIH (irq 39) nested IRQs [ 1.727935] twl_rtc rtc.15: Power up reset detected. [ 1.733825] twl_rtc rtc.15: Enabling TWL-RTC [ 1.740844] twl_rtc rtc.15: rtc core: registered rtc.15 as rtc0 [ 1.747650] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.753753] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.759826] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.766021] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.771545] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.777008] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.782470] VDAC: 1800 mV [ 1.782470] VANA: 2100 mV [ 1.789306] VCXIO: 1800 mV [ 1.789306] VUSB: 3300 mV [ 1.796203] V1V8: 1800 mV [ 1.799774] V2V1: 2100 mV [ 1.888946] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.019439] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 2.052337] hub 1-1:1.0: USB hub found [ 2.056427] hub 1-1:1.0: 5 ports detected [ 2.359436] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.580047] smsc95xx v1.0.4 [ 2.670043] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, e2:12:0c:0e:4d:b3 ~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.109 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-G7WltL/tmpNA9__a-uImage tftp 0x01000000 tmp/snowball-G7WltL/tmpNA9__a-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.109 Filename 'tmp/snowball-G7WltL/tmpNA9__a-uImage'. Load address: 0x1000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 4691017 (479449 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4690953 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK
Starting kernel ...
~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org